smartctl 5.43 2012-06-30 r3573 [i686-linux-3.10.4-pmagic] (local build) Copyright (C) 2002-12 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint S250 Device Model: SAMSUNG HD250HJ Serial Number: S0URJ9DPB28807 LU WWN Device Id: 5 0000f0 09bb28807 Firmware Version: FH100-05 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3b Local Time is: Sun Dec 18 17:22:39 2016 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3572) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 099 051 Pre-fail Always - 142 3 Spin_Up_Time 0x0007 253 253 025 Pre-fail Always - 4544 4 Start_Stop_Count 0x0032 093 093 000 Old_age Always - 7613 5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 20291 10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 253 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3374 13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 127854691 184 End-to-End_Error 0x0033 253 253 099 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 5448837 188 Command_Timeout 0x0032 253 253 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 148 124 000 Old_age Always - 30 (Min/Max 9/38) 194 Temperature_Celsius 0x0022 148 124 000 Old_age Always - 30 (Min/Max 9/38) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 127854691 196 Reallocated_Event_Count 0x0032 253 253 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 089 089 000 Old_age Always - 103 198 Offline_Uncorrectable 0x0030 253 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 100 072 000 Old_age Always - 133 202 Data_Address_Mark_Errs 0x0032 253 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 658 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 658 occurred at disk power-on lifetime: 20287 hours (845 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 2f 1b 60 e0 Error: UNC 8 sectors at LBA = 0x00601b2f = 6298415 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 2f 1b 60 e0 00 03:10:20.188 READ DMA ec 00 00 00 00 00 a0 00 03:10:14.563 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:10:14.563 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 00 03:10:14.563 IDENTIFY DEVICE Error 657 occurred at disk power-on lifetime: 20287 hours (845 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 2f 1b 60 e0 Error: UNC 8 sectors at LBA = 0x00601b2f = 6298415 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 2f 1b 60 e0 00 03:10:14.500 READ DMA ec 00 00 00 00 00 a0 00 03:10:10.188 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:10:10.188 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 00 03:10:10.188 IDENTIFY DEVICE Error 656 occurred at disk power-on lifetime: 20287 hours (845 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 17 01 60 e0 Error: UNC 8 sectors at LBA = 0x00600117 = 6291735 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 17 01 60 e0 00 03:10:10.125 READ DMA ec 00 00 00 00 00 a0 00 03:10:06.688 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:10:06.688 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 00 03:10:06.688 IDENTIFY DEVICE Error 655 occurred at disk power-on lifetime: 20287 hours (845 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 2f 1b 60 e0 Error: UNC 8 sectors at LBA = 0x00601b2f = 6298415 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 2f 1b 60 e0 00 03:10:06.625 READ DMA ec 00 00 00 00 00 a0 00 03:10:02.625 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:10:02.625 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 00 03:10:02.625 IDENTIFY DEVICE Error 654 occurred at disk power-on lifetime: 20287 hours (845 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 2f 1b 60 e0 Error: UNC 8 sectors at LBA = 0x00601b2f = 6298415 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 2f 1b 60 e0 00 03:10:02.563 READ DMA c8 00 08 0b 03 35 ec 00 03:09:58.000 READ DMA c8 00 08 0b f3 94 ec 00 03:09:58.000 READ DMA c8 00 00 0b f6 34 ec 00 03:09:57.938 READ DMA c8 00 00 0b f5 34 ec 00 03:09:57.938 READ DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.