smartctl 6.6 2017-11-05 r4594 [x86_64-w64-mingw32-w10-1607] (sf-6.6-1) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 Device Model: TOSHIBA HDWD130 Serial Number: 98M0ZJ6AS LU WWN Device Id: 5 000039 fe6eab917 Firmware Version: MX6OACF0 User Capacity: 3 000 592 982 016 bytes [3,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 02 18:34:10 2022 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Disabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (21648) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 361) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 092 092 016 - 2097163 2 Throughput_Performance P-S--- 140 140 054 - 67 3 Spin_Up_Time POS--- 132 132 024 - 436 (Average 433) 4 Start_Stop_Count -O--C- 100 100 000 - 1851 5 Reallocated_Sector_Ct PO--CK 001 001 005 NOW 1802 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 099 099 000 - 7343 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 927 192 Power-Off_Retract_Count -O--CK 089 089 000 - 13402 193 Load_Cycle_Count -O--C- 089 089 000 - 13402 194 Temperature_Celsius -O---- 171 171 000 - 35 (Min/Max 14/48) 196 Reallocated_Event_Count -O--CK 001 001 000 - 40788 197 Current_Pending_Sector -O---K 001 001 000 - 3880 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1385 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1385 [0] occurred at disk power-on lifetime: 7146 hours (297 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 88 00 00 52 77 0c 78 02 00 Error: UNC at LBA = 0x52770c78 = 1383533688 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 50 00 00 52 77 0d 00 40 00 02:04:16.079 READ FPDMA QUEUED 60 01 00 00 48 00 00 52 77 0c 00 40 00 02:04:16.079 READ FPDMA QUEUED 60 00 08 00 40 00 00 00 64 18 98 40 00 02:04:16.071 READ FPDMA QUEUED 40 00 00 00 01 00 00 00 00 00 01 00 00 02:04:06.606 READ VERIFY SECTOR(S) e0 00 00 00 00 00 00 00 00 00 00 00 00 02:00:49.874 STANDBY IMMEDIATE Error 1384 [3] occurred at disk power-on lifetime: 7127 hours (296 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 29 c1 37 f8 09 00 Error: UNC at LBA = 0x29c137f8 = 700528632 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 88 00 00 29 c1 37 f8 40 00 03:59:23.194 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 28 00 03:59:23.184 READ LOG EXT 60 01 00 00 88 00 00 29 c1 37 f8 40 00 03:59:10.557 READ FPDMA QUEUED 60 01 00 00 80 00 00 29 c1 36 f8 40 00 03:59:10.557 READ FPDMA QUEUED 60 01 00 00 78 00 00 29 c1 35 f8 40 00 03:59:08.414 READ FPDMA QUEUED Error 1383 [2] occurred at disk power-on lifetime: 7127 hours (296 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 98 00 00 29 c1 37 60 09 00 Error: UNC at LBA = 0x29c13760 = 700528480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 88 00 00 29 c1 37 f8 40 00 03:59:10.557 READ FPDMA QUEUED 60 01 00 00 80 00 00 29 c1 36 f8 40 00 03:59:10.557 READ FPDMA QUEUED 60 01 00 00 78 00 00 29 c1 35 f8 40 00 03:59:08.414 READ FPDMA QUEUED 60 01 00 00 70 00 00 29 c1 34 f8 40 00 03:59:08.414 READ FPDMA QUEUED 60 01 00 00 68 00 00 29 c1 33 f8 40 00 03:59:08.181 READ FPDMA QUEUED Error 1382 [1] occurred at disk power-on lifetime: 7127 hours (296 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 38 00 00 46 20 b9 b8 06 00 Error: UNC at LBA = 0x4620b9b8 = 1176549816 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 e0 00 00 46 20 b8 f0 40 00 03:56:06.644 READ FPDMA QUEUED 60 01 00 00 d8 00 00 46 20 b7 f0 40 00 03:56:06.644 READ FPDMA QUEUED 60 01 00 00 d0 00 00 46 20 b6 f0 40 00 03:55:22.928 READ FPDMA QUEUED 60 01 00 00 c8 00 00 46 20 b5 f0 40 00 03:55:22.928 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 28 00 03:55:22.918 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7343 - # 2 Short offline Aborted by host 90% 7343 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 23/35 Celsius Lifetime Min/Max Temperature: 14/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (48) Index Estimated Time Temperature Celsius 49 2022-01-02 16:27 35 **************** ... ..( 14 skipped). .. **************** 64 2022-01-02 16:42 35 **************** 65 2022-01-02 16:43 36 ***************** ... ..( 3 skipped). .. ***************** 69 2022-01-02 16:47 36 ***************** 70 2022-01-02 16:48 35 **************** ... ..( 7 skipped). .. **************** 78 2022-01-02 16:56 35 **************** 79 2022-01-02 16:57 34 *************** ... ..( 7 skipped). .. *************** 87 2022-01-02 17:05 34 *************** 88 2022-01-02 17:06 35 **************** 89 2022-01-02 17:07 35 **************** 90 2022-01-02 17:08 34 *************** 91 2022-01-02 17:09 34 *************** 92 2022-01-02 17:10 35 **************** ... ..( 18 skipped). .. **************** 111 2022-01-02 17:29 35 **************** 112 2022-01-02 17:30 ? - 113 2022-01-02 17:31 24 ***** 114 2022-01-02 17:32 25 ****** 115 2022-01-02 17:33 25 ****** 116 2022-01-02 17:34 26 ******* 117 2022-01-02 17:35 26 ******* 118 2022-01-02 17:36 27 ******** 119 2022-01-02 17:37 27 ******** 120 2022-01-02 17:38 27 ******** 121 2022-01-02 17:39 28 ********* 122 2022-01-02 17:40 28 ********* 123 2022-01-02 17:41 29 ********** ... ..( 2 skipped). .. ********** 126 2022-01-02 17:44 29 ********** 127 2022-01-02 17:45 30 *********** 0 2022-01-02 17:46 30 *********** 1 2022-01-02 17:47 31 ************ ... ..( 4 skipped). .. ************ 6 2022-01-02 17:52 31 ************ 7 2022-01-02 17:53 32 ************* ... ..( 5 skipped). .. ************* 13 2022-01-02 17:59 32 ************* 14 2022-01-02 18:00 33 ************** ... ..( 2 skipped). .. ************** 17 2022-01-02 18:03 33 ************** 18 2022-01-02 18:04 34 *************** ... ..( 2 skipped). .. *************** 21 2022-01-02 18:07 34 *************** 22 2022-01-02 18:08 35 **************** ... ..( 25 skipped). .. **************** 48 2022-01-02 18:34 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 927 --- Lifetime Power-On Resets 0x01 0x010 4 7343 --- Power-on Hours 0x01 0x018 6 15474776410 --- Logical Sectors Written 0x01 0x020 6 66793400 --- Number of Write Commands 0x01 0x028 6 13863688473 --- Logical Sectors Read 0x01 0x030 6 60846904 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 5929 --- Spindle Motor Power-on Hours 0x03 0x010 4 5926 --- Head Flying Hours 0x03 0x018 4 13402 --- Head Load Events 0x03 0x020 4 1802 --- Number of Reallocated Logical Sectors 0x03 0x028 4 11143 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1383 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 90 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 32 N-- Average Short Term Temperature 0x05 0x018 1 33 N-- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 14 --- Lowest Temperature 0x05 0x030 1 40 N-- Highest Average Short Term Temperature 0x05 0x038 1 24 N-- Lowest Average Short Term Temperature 0x05 0x040 1 38 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 5868 --- Number of Hardware Resets 0x06 0x010 4 4867 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS