smartctl 6.5 2016-05-07 r4318 [x86_64-w64-mingw32-win7-sp1] (sf-6.5-1) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: HGST Travelstar Z5K1000 Device Model: HGST HTS541010A7E630 Serial Number: S0A001SSGSEX7K LU WWN Device Id: 5 000cca 756caa8c1 Firmware Version: SE0OA4A0 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Feb 27 19:49:10 2018 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 1 (minimum power consumption with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 221) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 163 163 033 - 1 4 Start_Stop_Count -O--C- 073 073 000 - 43042 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 080 080 000 - 8900 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1089 191 G-Sense_Error_Rate -O-R-- 098 098 000 - 131075 192 Power-Off_Retract_Count -O--CK 100 100 000 - 17 193 Load_Cycle_Count -O--C- 089 089 000 - 113619 194 Temperature_Celsius -O---- 193 193 000 - 31 (Min/Max 10/47) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 8 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 20 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 20 [3] occurred at disk power-on lifetime: 8871 hours (369 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 2a 00 00 0d 21 80 28 0d 00 Error: UNC 42 sectors at LBA = 0x0d218028 = 220299304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 0d 21 80 12 e0 00 02:49:46.038 READ DMA EXT 25 00 00 00 40 00 00 0d 21 7f d2 e0 00 02:49:46.038 READ DMA EXT 25 00 00 00 40 00 00 0d 21 7f 92 e0 00 02:49:46.038 READ DMA EXT 25 00 00 00 40 00 00 0d 21 7f 52 e0 00 02:49:46.038 READ DMA EXT 25 00 00 00 40 00 00 0d 21 7f 12 e0 00 02:49:46.037 READ DMA EXT Error 19 [2] occurred at disk power-on lifetime: 8826 hours (367 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 0d 21 80 28 0d 00 Error: UNC 8 sectors at LBA = 0x0d218028 = 220299304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 0d 21 80 28 e0 00 01:48:09.918 READ DMA EXT 35 00 00 00 08 00 00 00 5f 0f 08 e0 00 01:48:09.918 WRITE DMA EXT 25 00 00 00 08 00 00 3e 34 47 08 e0 00 01:48:09.911 READ DMA EXT 25 00 00 00 80 00 00 3e 24 e6 b0 e0 00 01:48:09.893 READ DMA EXT 25 00 00 00 40 00 00 0e 24 c7 40 e0 00 01:48:09.853 READ DMA EXT Error 18 [1] occurred at disk power-on lifetime: 8826 hours (367 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 0d 21 80 28 0d 00 Error: UNC 8 sectors at LBA = 0x0d218028 = 220299304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 0d 21 80 28 e0 00 01:48:05.963 READ DMA EXT 25 00 00 00 08 00 00 0c d0 c0 80 e0 00 01:48:05.938 READ DMA EXT 35 00 00 00 10 00 00 06 31 0f 38 e0 00 01:48:05.938 WRITE DMA EXT 35 00 00 00 08 00 00 05 2c b4 55 e0 00 01:48:05.938 WRITE DMA EXT 35 00 00 00 18 00 00 00 5f ea f8 e0 00 01:48:05.938 WRITE DMA EXT Error 17 [0] occurred at disk power-on lifetime: 8826 hours (367 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 0d 21 80 28 0d 00 Error: UNC 8 sectors at LBA = 0x0d218028 = 220299304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 0d 21 80 28 e0 00 01:48:01.927 READ DMA EXT 35 00 00 00 10 00 00 06 31 0f 08 e0 00 01:48:01.927 WRITE DMA EXT 25 00 00 01 00 00 00 0d 21 82 00 e0 00 01:48:01.907 READ DMA EXT 35 00 00 00 30 00 00 06 31 0e c8 e0 00 01:48:01.906 WRITE DMA EXT 35 00 00 00 08 00 00 05 2c b4 4d e0 00 01:48:01.906 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 17/31 Celsius Lifetime Min/Max Temperature: 10/47 Celsius Lifetime Average Temperature: 31 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (83) Index Estimated Time Temperature Celsius 84 2018-02-27 17:42 34 *************** 85 2018-02-27 17:43 34 *************** 86 2018-02-27 17:44 34 *************** 87 2018-02-27 17:45 33 ************** ... ..( 6 skipped). .. ************** 94 2018-02-27 17:52 33 ************** 95 2018-02-27 17:53 32 ************* 96 2018-02-27 17:54 33 ************** 97 2018-02-27 17:55 33 ************** 98 2018-02-27 17:56 32 ************* 99 2018-02-27 17:57 33 ************** 100 2018-02-27 17:58 32 ************* ... ..( 4 skipped). .. ************* 105 2018-02-27 18:03 32 ************* 106 2018-02-27 18:04 33 ************** 107 2018-02-27 18:05 32 ************* ... ..( 15 skipped). .. ************* 123 2018-02-27 18:21 32 ************* 124 2018-02-27 18:22 33 ************** ... ..( 11 skipped). .. ************** 8 2018-02-27 18:34 33 ************** 9 2018-02-27 18:35 32 ************* 10 2018-02-27 18:36 33 ************** ... ..( 18 skipped). .. ************** 29 2018-02-27 18:55 33 ************** 30 2018-02-27 18:56 32 ************* 31 2018-02-27 18:57 33 ************** ... ..( 5 skipped). .. ************** 37 2018-02-27 19:03 33 ************** 38 2018-02-27 19:04 34 *************** 39 2018-02-27 19:05 ? - 40 2018-02-27 19:06 19 - 41 2018-02-27 19:07 21 ** 42 2018-02-27 19:08 21 ** 43 2018-02-27 19:09 22 *** 44 2018-02-27 19:10 23 **** 45 2018-02-27 19:11 23 **** 46 2018-02-27 19:12 23 **** 47 2018-02-27 19:13 25 ****** ... ..( 4 skipped). .. ****** 52 2018-02-27 19:18 25 ****** 53 2018-02-27 19:19 26 ******* 54 2018-02-27 19:20 26 ******* 55 2018-02-27 19:21 26 ******* 56 2018-02-27 19:22 27 ******** ... ..( 2 skipped). .. ******** 59 2018-02-27 19:25 27 ******** 60 2018-02-27 19:26 28 ********* ... ..( 2 skipped). .. ********* 63 2018-02-27 19:29 28 ********* 64 2018-02-27 19:30 29 ********** ... ..( 2 skipped). .. ********** 67 2018-02-27 19:33 29 ********** 68 2018-02-27 19:34 28 ********* 69 2018-02-27 19:35 29 ********** 70 2018-02-27 19:36 28 ********* 71 2018-02-27 19:37 28 ********* 72 2018-02-27 19:38 29 ********** 73 2018-02-27 19:39 29 ********** 74 2018-02-27 19:40 30 *********** ... ..( 3 skipped). .. *********** 78 2018-02-27 19:44 30 *********** 79 2018-02-27 19:45 31 ************ 80 2018-02-27 19:46 31 ************ 81 2018-02-27 19:47 30 *********** 82 2018-02-27 19:48 31 ************ 83 2018-02-27 19:49 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS